Thus it is necessary to take the proper precautions. It all depends on the designers what he or she would prefer to use in the power supply circuit. The most common part number for power IC is UC and it has 8 pins. It consists of primary and secondary section and has different types of components in it to make the power supply to work. In some data books, there would be suggestions as to which part numbers are suitable for replacement. This is because the hot side of the AC line essentially goes to all power supply components on the primary side of transformer.
| Uploader: | Mikara |
| Date Added: | 16 April 2011 |
| File Size: | 64.56 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 55190 |
| Price: | Free* [*Free Regsitration Required] |
If you carefully trace the drain and the positive pin of the filter capacitor, it will eventually bring you to the two pins of the switch mode power transformer. From there, rwpair can make some conclusions as where to begin to check first i. If others are searching for it toohere's http: If I have it, I will give the information value of the components to them. Assuming you come across such SMPS, what would you do?
Troubleshooting & Repairing Switch Mode Power Supplies - PDF Free Download
If you have used an oscilloscope before, then you probably know just how useful they can be. The large filter capacitor in the power supply section can hold dangerous high voltage even if the unit has been switched off for a few days. Your precious time will be wasted because you could not effectively locate the bad component which is the coils.
It should not show any steady reading pdff both directions. Blue ESR meter is a powerful ESR meter, user friendly, robust, versatile and capable in locating bad or shorted electrolytic capacitor while still in the circuit. This section only explains one part of the way to repair switch mode power supply.
If you did not turn it off, the replacement component suply burn or short after a period of time. Please visit the link at page to find out the capabilities of using Blue ESR meter to test on other components besides electrolytic capacitors http: Let say the part number is UC, go to Google dot com and key in one of these keywords as shown below to look up for the data: ;ower just a simple voltage test on certain components or area yonf the SMPS, you can easily conclude whether the component or the circuit section is faulty or not.
Troubleshooting & Repairing Switch Mode Power Supplies
Look at the power LED of the equipment and if it blinks, then it is a power blinking problem. This indicates the problem is in the regulation circuit like an open resistor in feedback circuit, bad Optoisolator IC, faulty TL IC and etc.
The authors and publisher make no representation or warranties mestine respect to the accuracy, applicability, fitness, or completeness of the contents of this program.
The SMPS tries to start up but because there are some components failures either at the primary or the secondary section, jeestine power went down again and the cycle goes on.
Whenever you come across a blown fuse, please test the bridge rectifier first before you replace it with a new fuse and retest the power supply. Tags playstation 2 power supply repair guide power supply repair guide power supply repair guide book power supply repair guide by jestine yong power supply repair guide download.
The changing magnetic field induces voltage in the secondary windings. Jesfine Run DC circuit that consists of a resistor and a diode will maintain the power IC stable operation.
Every electronic technician must always take safety precautions before he or she starts work. The function of the capacitors is to suppress the RFI signals generated by the rectifier diodes.
SMPT rarely has problems but when it encounters problems, the main fuse will usually blow and the components in the primary side may be affected as well. The short circuit caused by the lizard blew up many components in the power supply. Secondary Output Voltage circuit 6.
A switch mode power supply, also called switcher, is just a power supply device that is used to convert the volt and current features from one form to some other. Your investment on the tools and test equipment will pay itself back in a very short period, provided if you have lots of equipment SMPS for you to repair. Always look for the replacement that has the same or higher specification in terms of Voltage, Ampere and Wattage.
For your information, not all equivalent part number can be used as some of them would short again after sometimes due to incompatibility in the semiconductor specification.
If you have confirmed that the primary side is the cause of the problem then check all of the components in this area. Regardless of which name you choose to call them, multimeters are the handiest and most versatile piece of test equipment that you will ever use. Please keep on reading on the next four methods.
These components can be easily damaged by static electricity. Sometimes under heavy short circuit in the power supply, these capacitors could crack and will have burnt mark and split open.
Комментарии
Отправить комментарий